Strategy B9. Provide Right-Turn Acceleration Lanes at Intersections

NCHRP Report 500 / Volume 5: A Guide for Addressing Unsignalized Intersection Collisions

WHERE TO USE

Unsignalized intersections that experience a high proportion of rear-end and/or sideswipe crashes related to the speed differential caused by vehicles making a right-turn maneuver onto the highway.

Photograph of an intersection with a rural highway. Right turning vehicles entering the highway have a lengthy stretch of acceleration lane to the right of the highway through lanes.
Photo by: Texas Transportation Institute

DETAILS

Drivers turning onto an uncongested highway accelerate until the desired open-road speed is reached. When acceleration by entering traffic takes place directly on the traveled way, it may disrupt the flow of through-traffic. To minimize this operational problem due to right-turning traffic at divided highway intersections, right-turn acceleration lanes may be used. An acceleration lane is an auxiliary or speed-change lane that allows vehicles to accelerate to highway speeds before entering the through-traffic lanes of a highway. Acceleration lanes should be of sufficient length to permit adjustments in speeds of both through and entering vehicles so that the driver of the entering vehicle can position the vehicle opposite a gap in the through-traffic stream and maneuver into that gap before reaching the end of the acceleration lane.

KEY TO SUCCESS

Make sure that right-turn acceleration lanes are operationally warranted by relatively high right-turn volumes or justified on the basis of an existing pattern of rear-end or sideswipe crashes related to right-turn maneuvers.

ISSUES

If a right-turn acceleration lane is excessively long or poorly marked, through drivers may mistake it for an additional through lane.

There is little guidance available on the best geometric design for right-turn acceleration lanes. Both parallel and tapered acceleration-lane designs have been used. The AASHTO Policy on Geometric Design for Highways and Streets provides guidance on the design of acceleration lanes for freeway entrance ramps, but there is no specific design guidance for acceleration lanes at intersections.

Installation of right-turn acceleration lanes increases the overall width of the intersection. Therefore, the additional width may cause potential problems for pedestrians crossing the intersection. One possible solution to this problem is to provide a pedestrian refuge island in the median.

TIME FRAME: Medium

Time for implementation of right-turn acceleration lanes at intersections may vary from 3 months to 4 years. At some locations, right-turn acceleration lanes can be constructed simply by restriping the roadway. At other locations, widening the roadway, cutting further into a shoulder, or acquiring additional right-of-way may be needed. Such projects may require a substantial time for development and construction. Where additional right-of-way is required or where the environmental process requires analysis and documentation, project implementation may take up to 4 years.

COSTS: Moderate

Costs are highly variable. Where sufficient roadway or shoulder width to provide a right-turn acceleration lane is available, it may be possible to provide a right-turn acceleration lane at moderate cost. Where additional right-of-way must be acquired, higher costs are likely.

EFFECTIVENESS

TRIED: By removing the slower right-turning vehicles from the through lanes, this strategy is expected to reduce rear-end and sideswipe crashes resulting from conflicts between vehicles making a right turn maneuver onto the highway and through vehicles on the highway. Research has shown that right-turn acceleration lanes at intersections function effectively and do not create safety problems. However, no quantitative estimates of the safety effectiveness of right-turn acceleration lanes at intersections are available.

COMPATIBILITY

This strategy can be used in conjunction with other strategies for improving safety at unsignalized intersections.

For more details on this and other countermeasures: http://safety.transportation.org



For more information contact:

FHWA Office of Safety Design
E71, 1200 New Jersey Avenue SE
Washington, D.C. 20590
(202) 366-9064
http://safety.fhwa.dot.gov

FHWA Resource Center – Safety and Design Team
19900 Governor's Drive, Suite 301
Olympia Fields, IL 60461
(708) 283-3545
http://www.fhwa.dot.gov/resourcecenter

Logo for FHWA and logo for the FHWA Office of Safety, which reads 'Safe Roads for a Safer Future – Investment in roadway safety saves lives.'

Previous | Next

Program Contact

Ed Rice

202-366-9064

Jeffrey Shaw

708-283-3524

What’s New

Roundabout Outreach and Education Toolbox

Stop-Controlled Intersection Safety: Through Route Activated Warning Systems

Roundabouts: An Informational Guide, Second Edition (NCHRP Report 672)

Roundabouts Peer-to-Peer Assistance

How to drive a roundabout (WSDOT)

Modern Roundabouts: A Safer Choice

FHWA's Intersection Resources Library CD-ROM

Highlights

Roundabouts Technical Summary

Mini-Roundabouts Technical Summary

Access Management in the Vicinity of Intersections Technical Summary

Intersection Safety Case Studies

Intersection Safety Technologies

Presentation: Intersection Safety

Example Intersection Safety Implementation Plan

Intersection Safety Implementation Plan Workshop

Example Data Analysis Package and Straw Man Outline